+1 (954) 946-9454

Microm II Digital Film Applicators

Article No. 10592

Microm II Digital, 12”/30.5 cm

  • Digital Microm II Film Applicator
  • 12"/30.5 cm film width
  • Mils and Microns
  • Standard anodized aluminum side plates 
  • Standard 400 series stainless-steel blade

More options

Material
Film Width
$2,274.00 excl. taxes & shipping cost

Features

  • Microm II Digital Film Applicator is a casting knife film applicator with a digital LCD display of measurements shown in both mils and microns.
  • All digital models include spindle and lock feature to hold measurements in place
  • 0.00005" (0.001mm) digital graduation
  • Digital LCD display with inch and metric readout
  • SPC output transmits results to a computer or external device through an interface cable (sold separately)
  • Ingress Protection to IP65
  • Satin chrome finish on thimble sleeve helps resist rust
  • Metal Magnet bushing
  • Knife-blade fitted into slots in the end section allows vertical adjustment of the blade
  • The ends of the side plates also serve as ergonomic operator hand grips when drawing down wet films
 
  • Two types of side plates available that provide large paint well:
    • Standard side plates are made from special clear anodized aluminum
    • Tefcrom side plates are Teflon coated for lowest coefficients of friction against any solid. They are non-reactive and are great for films cast on thin substrates as it helps prevent tearing by minimizing friction with the substrate
  • Two types of blades are available:
    • The standard blade is finely machined 400 series stainless steel
    • The Teflon blade is coated with a tough, durable PTFE film that provides excellent non-stick properties which makes for easy cleaning and good corrosion resistance. It also makes the blade more durable with exceptionally good abrasion resistance
  • Rare earth magnets hold blade firmly in place. (The 2" applicator does not utilize the rare earth magnets and only uses one non rotating spindle micrometer that is fixed to the blade via two set screws.)
  • Casting knife film applicator with patented magnetic blade attachment for easy cleaning - US Patent 7,930,991
  • No springs to break, rust or get clogged
  • Extreme Accuracy
  • Ergonomic design facilitates fast and accurate drawdowns
  • Special orders welcome

Technical Attributes

  • Film Width
    12”/30.5 cm
  • Material
    Standard with Standard blade
  • Data
    Models:ImperialMetricDigital
    Measurement Type:MilsMicronsMils/Microns
    Measurement Range:0-0.250”0-6.35mm0.00005" (0.001mm)
    Side Plate Options:Aluminum (Standard) or Teflon (Tefcrom)
    Blade Options:Stainless Steel (Standard) or Teflon
    Locking Mechanism:--Included
    Display:AnalogAnalogDigital Display

Standards

ASTM

D823

Procedure

Before use, check the zero settings of the micrometers. Place applicator on a polished granite flat plate or alternatively plate-glass of suitable size. Set micrometers at zero. The blade should touch the glass/granite flat plate from end to end without the side plate being elevated. When the applicator is placed between the observer and a bright back light the user should see no light from beneath the blade and side plates. The zero point should check within ± 0.0005". If not press the Zero button on the digital micrometer to reset the reading to zero. Repeat if necessary to assure a proper zero is achieved. Cautionary Note: Make sure that there is no foreign matter such as iron fillings adhering to the blade magnets as this might result in improper applicator calibration.

  1. Place applicator at upper end of test panel.
  2. Pour coating directly in front of the knife-blade.
  3. Draw applicator toward lower end of panel at an approximate uniform rate of 10 to 12 inches (250-300mm) per second.
  4. Clean applicator immediately after use and thoroughly dry the blade. Caution: Do not wet or submerse micrometer heads.
Join our Email List. subscribe
CANCEL