Microm II Digital Film Applicators

Art. No.: 10594

Microm II Dig. Tefcrom, 12"/30.5 cm

Digital Microm II Film Applicator
12" / 30.5 cm film width
Mils and Microns
Cerakote coated side plates
Standard 400 series stainless-steel blade

Caution: Do not wet or submerse micrometer heads.

Select your Model

Material

Film Width

€2,256.00

QTY

Enter a value between 1 and 100000000 in increments of 1.

excl. taxes & shipping cost

Microm II Digital Film Applicator is a casting knife film applicator with a digital LCD display of measurements shown in both mils and microns.
All digital models include spindle and lock feature to hold measurements in place
0.00005" (0.001mm) digital graduation
Digital LCD display with inch and metric readout
SPC output transmits results to a computer or external device through an interface cable (sold separately)
Ingress Protection to IP65
Satin chrome finish on thimble sleeve helps resist rust
Metal Magnet bushing
Knife-blade fitted into slots in the end section allows vertical adjustment of the blade
The ends of the side plates also serve as ergonomic operator hand grips when drawing down wet films
Two types of side plates available that provide large paint well:
- Standard side plates are made from special clear anodized aluminum
- Tefcrom side plates are Cerakote coated for lowest coefficients of friction against any solid. They are non-reactive and are great for films cast on thin substrates as it helps prevent tearing by minimizing friction with the substrate
Two types of blades are available:
- The standard blade is finely machined 400 series stainless steel
- The Cerakote blade is coated with a tough, durable PTFE film that provides excellent non-stick properties which makes for easy cleaning and good corrosion resistance. It also makes the blade more durable with exceptionally good abrasion resistance
Rare earth magnets hold blade firmly in place. (The 2" applicator does not utilize the rare earth magnets and only uses one non rotating spindle micrometer that is fixed to the blade via two set screws.)
Casting knife film applicator with patented magnetic blade attachment for easy cleaning - US Patent 7,930,991
No springs to break, rust or get clogged
Extreme Accuracy
Ergonomic design facilitates fast and accurate drawdowns
Special orders welcome

Technical Data Chart

Data

Models:	Imperial	Metric	Digital
Measurement Type:	Mils	Microns	Mils/Microns
Measurement Range:	0-0.250”	0-6.35mm	0-250” / 0-6.35mm
Side Plate Options:	Aluminum (Standard) or Cerakote (Tefcrom)
Blade Options:	Stainless Steel (Standard) or Cerakote
Locking Mechanism:	-	-	Included
Display:	Analog	Analog	Digital Display

ASTM	D823

Microm II Dig. Tefcrom, 12"/30.5 cm

Place applicator at upper end of test panel.
Pour coating directly in front of the knife-blade.
Draw applicator toward lower end of panel at an approximate uniform rate of 10 to 12 inches (250-300mm) per second.
Clean applicator immediately after use and thoroughly dry the blade. Caution: Do not wet or submerse micrometer heads.

Digital Micrometer Zero Setting

Preparation:
Place the applicator on a polished granite flat plate or a suitable plate-glass surface.
Set Micrometers to Zero:
Ensure the blade touches the flat plate evenly from end to end without elevating the side plate.
Check for Light Gaps:
Position the applicator between you and a bright backlight.
Verify no light is visible beneath the blade and side plates.
Verify Zero Point Accuracy:
Confirm the zero point.
If necessary, press the Zero button on the digital micrometer to reset the reading.
Repeat the check until proper zero is achieved.
Final Inspection:
Ensure no foreign matter, such as iron filings, is adhering to the blade magnets, as this may affect calibration.