+1 (954) 946-9454

Dual Guide Tool Crosscut Tester

Article No. 12618

Cross Hatch Adhesion Dual Tool ASTMd3359

The Dual Guide Tool Crosscut Tester is a metal shim assembly model with spacings up to 6mm, which are required for some bridge and industrial applications.

$362.00 excl. taxes & shipping cost

Features

  • A very compact instrument for making 1.0, 1.5, 2.0, 3.0, 4.0, 4.5, 5.0 and 6.0mm spaced crosscuts on both smooth and flat surfaces as well as somewhat rough coated surfaces.
  • Makes 8 spaced crosscuts on both smooth and flat surfaces
  • Magnetic base to hold this very compact instrument secure on ferrous substrates such as steel panels, bridges, ships, etc.
  • Made from high grade materials, the aluminum body of the gauge is black anodized for durability and corrosion resistance, the 1mm and 1.5mm shims are made from stainless steel.
  • Suggested for adhesion tests on bridges, ships, etc. 
  • Note progressive positions of shims after each cut has been made.
  • Length of cutter knife blade may be adjusted to any length to facilitate position of cutting procedure.
  • Multiple cuts in a test specimen must be evenly spaced if results are to be meaningful and repeatable. To insure even spacing of the cuts, a specially designed, versatile instrument with Blade Guides or Metal Shims.
  • Dimensions of the assembly are 1cm thick, 6 cm wide and 8.5 cm long.
  • When not being used, it retracts into a plastic housing for protection.
  • There are scores in the blade which permits the end to be snapped away so that up to thirteen fresh sharp tips may be exposed.
  • The entire blade is readily replaceable in the handle.
  • Kit available in accessories to complete a cross hatch adhesion test

Standards

Meets ASTM D3359 and ASTM F1842

Procedure

  1. Prepare the test specimen and select the area for test as outlined in ASTM D3359. Inspect the tip of the cutter knife and, if dull from prior use, remove top plastic cap and with only one segment of the cutter extending from the protective plastic housing, place cap over end of the blade and snap off the end segment.
  2. Select the thickness of the cuts to be used and remove the lower shoulder bolt from the metal shims of the Dual Shim Assembly which are of this thickness.
  3. Place the non-slip instrument on test surface, with all shims in the lowered position. Make the first cut drawing the blade downward with light pressure against the shim in a manner similar to making a straight line with a straight edge. Without moving position of instrument on the test surface rotate the first shim upward and out of the way of the second shim so that second cut can be made using second shim as a guide.
  4. Repeat this process until all shims have been rotated upward. Since there are ten shims there will be eleven uniform cuts. Next, rotate the instrument 90° on the test surface and repeat the above procedure to place the same number of uniform cuts intersecting those first produced. Proceed with test outlined in ASTM D3359.

The procedure for making 3mm spaced cuts is identical to the above except two of the shims are rotated upward following each cut. Six equally spaced cuts are produced when operating in this mode. Cuts spaced at 2mm are produced by using the 1mm shims, rotated two at a time for each cut. You can have all of the following mm spacings and still have three cuts in each direction in the cross cut pattern: 1, 1.5, 2, 3, 4, 4.5, 5 and 6. According to discussions heard in the ASTM, the larger spacings are required in some “bridge” and industrial work.

Delivery Content

Dual Guide Kit - (Does not include Dual Guide Tool) Flaking brush, Illuminated magnifier w/batteries, One roll of (51596) tape, Knife, Hex wrench, Foam lined attache type plastic carrying case w/ handle

Join our Email List. subscribe
CANCEL